C3-340 CORIOmatrix is based on TV One's exclusive
CORIO®2 technology and provides high quality modular
video matrix switching using CORIOsoftswitch, which
provides an industry first firmware based video routing,
switching and video conversion platform. 16 AV module
slots are available. Additional DVI-U or 3G-SDI modules
can be added later.
By choosing scaled output modules, the CORIOmatrix
also provides Up, Down and Cross conversion between a
variety of analog and digital video formats thru 3G-SDI.
The modules selected determine what format will be
accommodated and the matrix size. Signal parameters of
the incoming video may be adjusted. All settings are
stored in non-volatile memory and are retained even
when power is switched off.
All the functions can be controlled
via serial connection via RS-232 or IP. Windows software
is provided for both video and audio routing and setup of
the router and can be used as the main control interface
if desired. Third party controllers using the built-in
command line interface easily permits a wide choice of
control options. The unit is housed in a standard 4RU
rackmount case and features an optional redundant hot
swappable internal PSU and power inlet.
The CORIOmatrix includes advanced Digital Flicker
Elimination circuitry and high 4:4:4 full bandwidth
sampling rate ensures crisp, clear images, while full
bandwidth chroma sampling ensures faithfully
reproduced, high resolution colors. Pixel Level Motion
Adaptive Diagonal Interpolation and Noise Reduction
ensures high quality de-interlacing of PAL, NTSC and
1080i signals. 3:2 Pull-down ensures proper 24 fps film
extraction from NTSC and 1080i sources.
Integral audio switching is provided to route audio from
the DVI (HDMI-compatible) input or SDI input to the DVI
and SDI outputs. An optional Audio Module can provide
AES and analog or digital I/O breakout capabilities as
well as audio delay and can link to our A2-7300 range of
audio break-out units. Audio routing control is
implemented in the Windows software and also available
using the command line interface.
The DVI-U universal interface utilizes a single DVI-I
connector to provide the following signal formats: HDMI,
DVI-I, plus analog YUV, YPbPr, RGBHV, RBBS, RGsB,
Y/C and Composite Video. A variety of adapters are
available to convert from DVI-I to other connectors.
The system features the following types of modules for
the inputs and outputs. All modules only use 1 AV Slot.
- DVI-U Universal Input Module - 2 Inputs
- DVI-U Universal Scaling Output Module - 2 Outputs
The DVI-U output module with scaling allows any input to
be converted to any of the DVI-U formats on the output.
The high resolution DVI-U outputs are selectable as
virtually any PC or HDTV resolution. NTSC, PAL, PAL-M,
PAL-N, SECAM standards are supported.
- 3G/HD/SD-SDI Input Module - 2 Inputs
- HD/SD-SDI Input Module - 4 Inputs
- 3G/HD/SD-SDI Output Scaling Module - 2 Outputs
- HD/SD-SDI Output Scaling Module - 4 Outputs*
- 3G/HD/SD-SDI Output (non-scaling) Module - 2 Out*
- 3G/HD/SD-SDI In/Out (non-scaling) Module-1 In 1 Out*
- HD/SD-SDI Output Non-Scaling Module - 4 Outputs*
A single monitoring card allows the inputs and outputs to
be viewed on 1 or 2 outputs for signal verification.
Embedded audio signals can be monitored along with
source and destination identification. A separate DVI-U
and 3G/HD/SD-SDI version of this module is available.
The optional CM-AUD-8IN-8OUT Audio Interface Module
allows connection to any of the following optional external
breakout units via HD-44 Connector.
- A2-7312 Converts AES-3id I/O to 16x BNC Connectors
8x AES-id In and 8x AES-3id Out
- A2-7302 Converts AES-3id I/O to 16x XLR Connectors
8 AES Stereo In and 8x Stereo Out
- A2-7342 Converts AES-3id I/O to 16x XLR Connectors
4x Analog Stereo In & 4x Analog Out
- A2-7322 Converts AES-3id I/O to Analog Stereo on
Terminal Blocks, 8x Analog Stereo In and 8x Analog
Stereo Out, Balanced or Unbalanced
Additional types and formats of Video, Audio and Data
Modules will be added in the future.